User manual BEKO WMA520

[. . . ] Any resultant damage is not covered by the warranty. Feet adjustment To ensure quiet and stable operation, the machine should be positioned correctly and on the level. If the machine is unstable, adjust one of the front feet by loosening the plastic lock nut and screwing or unscrewing the foot until the machine is level. After positioning, tighten the lock nut. 5 5 Water inlet connections Your machine comes with both cold and hot water connections. Connect the cold water using the hose with blue printing and connect the hot water using the hose with red printing. [. . . ] · The minimum diameter of any external pipe must be 32 mm. 6 electrical connection Make sure that you have an earthed power outlet socket rated at 13 amps (minimum). If you use your machine as built-in, the socket must be reachable after installation, or a separate switch (which can disconnect the two poles) must be used in the installation. Connect the power cord to the appropriate electrical socket with an equivalent current rating indicated on the rating plate at the front of the machine behind the kick plate. After removing the plug from its transit position, please insert the plug seal to prevent water spillage entering the machine. Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows: 1 Connect the green - yellow or green (earth) wire to the terminal in the plug marked `E' or with the symbol f or coloured green and yellow or green. 2 Connect the blue (neutral) wire to the terminal in the plug marked `N' or coloured black. 3 Connect the brown (live) wire to the terminal in the plug marked `L' or coloured red. With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box. Green and yellow or green Important Electrical requirements Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply. We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a Beko Authorised Service Agent. Warning This appliance must be earthed f If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house. If no spin is desired, you should leave the rinse hold button pressed in. Turn off the machine, select the letter D on the programme selection knob and turn on the machine. During this operation, water in the machine will be discharged. Amounts Follow the manufacturer's recommended amount of detergent given on the packaging. Adjust the amount according to the dirt level, the amount of fabric and the softness of the water. For example, if a small amount of clothing is washed, put in half the amount of detergent normally required. · Do not fill the fabric softener above the max mark as any excess amount will mix into the wash water and you will have to re-fill the compartment. Unloading The machine stops automatically after programmes are completed. 2 The door can be opened by gently pulling the door open handle 1-2 minutes after the washing cycle is completed. 3 Unload the machine, and leave the door open to air the interior. 9 programme descriptions No. Wash the drawer in warm water to remove detergent residue and before replacing wipe out the housing. Syphon The syphon (coloured insert in the dispenser) must be cleaned every 30-40 washes. Remove the dispenser drawer and lift out the syphon and wash in warm water to remove any softener residue. Refit ensuring that the syphon is correctly fitted before use. Maintenance wash If you regularly use low temperature programs, certain detergents cause build up of greasy deposits over time. [. . . ] To prevent objects entering the pump and causing damage, your machine employs a filter system that extends the pump life. Turn the opening of kick plate screws 90° with the help of a screw driver or a coin. Place a little pan in front of the filter door to catch the small amount of water spilling from the machine. After cleaning the filter, replace it by turning clockwise making sure that it is closed firmly. [. . . ]