User manual BEKO HIZE 64101 DIMENSIONS

[. . . ] p Sensor switch for setting the time q Time display r Indicator lamp for automatic switch-off, e. g. of the rear right cooking zone s Indicator lamp for minute minder Cooking zones Cooking zone KM 5731 / KM 5752 / HIZE 64101 / KM 5757 minimum to maximum Ø in cm* 14 - 20 14 - 20 16 - 23 10 - 16 Rating in watts for 230 V** normal: with booster: normal: with booster: normal: with booster: normal: with booster: Total: * Pans of any base diameter within the given range may be used. ** The wattage quoted may vary depending on the size and material of the pans used. 1850 2500 1850 2500 2300 3200 1400 1800 7400 y w x z 12 Guide to the appliance Cooking zone KM 5732 / KM 5736 minimum to maximum Ø in cm* 14 - 20 10 - 16 16 - 23 10 - 16 Rating in watts for 230 V** normal: with booster: normal: with booster: normal: with booster: normal: with booster: Total: Cooking zone minimum to maximum Ø in cm* f 18 - 28 14 - 20 10 - 16 KM 5733 Rating in watts for 230 V** normal: with booster: normal: with booster: normal: with booster: Total: * Pans of any base diameter within the given range may be used. [. . . ] When the booster is switched on, the following happens: ­ if Auto heat-up is activated on either zone in the same network, this will be switched off. ­ the power level on the other linked cooking zone will sometimes decrease. Proceed as follows: ^ Touch the B sensor for the relevant cooking zone. Power setting 9 will show in the cooking zone display, and the indicator lamp for the booster will also light up. After 10 minutes, the zone will automatically revert to power setting 9. To switch off the booster before this, touch either the B sensor or the sensor for the appropriate cooking zone. If a power setting is selected before the booster function is switched on, the zone will revert to this pre-selected power setting when the booster is switched off, or automatically at the end of the booster time. 32 Use Switching off and residual heat indicators To switch off a cooking zone: ^ Touch the - and + sensors for the zone you want to switch off at the same time. If the cooking zone is still hot, residual heat will then be indicated in the display. The lines of the residual heat indicator go out one after another as the cooking zones cool down. The last horizontal line only goes out when the cooking zone is safe to touch. The residual heat indicators also react to hot dishes and plates being placed on a cooking zone that is not switched on. Do not touch any zone or place any heat sensitive items on a zone where the residual heat indicator is lit up. Power setting* Maximum operating time in hours 10 5 5 4 3 2 2 2 1 Safety switch-off if the sensors are covered Your hob will switch off automatically if one or several of the sensors remain covered for longer than 10 seconds, for example, by finger contact, food boiling over or by an object such as an oven glove or tea towel. An audible tone will sound every 30 seconds (for a maximum of ten minutes) and an F will flash in the display for the sensor which is covered. 1 / 1. The cooking zones can now be used again as normal. * The power settings with a dot after the number are only available if the power setting range has been extended (see "Programming - P6. "). ^ To use the cooking zones again, switch the hob back on in the usual way. 36 Safety features Overheating protection All of the induction coils and the cooling element for the electronics are fitted with an overheating protection mechanism. To prevent the induction coils and cooling element from overheating, the overheating protection mechanism works on the affected cooking zone or on the entire hob in the following ways: ­ If the booster function is being used, this will be switched off. The cooking zone can be used again as soon as it has cooled down to a safe level. ­ If the cooling element is affected, the power supply to the cooking zones will be reduced, and the set power level will continue to be displayed. As soon as the cooling element has cooled down sufficiently, the cooking zones will automatically continue to operate at the original power setting. Overheating can be caused by: ­ heating up an empty pan ­ fats or oils being heated up on the highest power setting. ­ there being insufficient ventilation to the under side of the appliance. If the overheating protection mechanism triggers again, contact the Service department. 37 Timer The hob is fitted with a timer which can be used both as a minute minder and to switch off the cooking zones automatically. [. . . ] Do not use sealant between the frame of the top part of the hob and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the frame or the worktop. 62 Installation Flush-fitted hobs Building-in dimensions for KM 5737 a Front b Building-in depth c Mains connection cable, L = 1440 mm d Stepped cut-out for granite or marble worktops Cut-out dimensions for granite or marble worktops. Please take careful note of the inset diagram. 63 Installation Building-in dimensions for KM 5757 a Front b Building-in depth c Mains connection cable, L = 1440 mm d Stepped cut-out for granite or marble worktops Cut-out dimensions for granite or marble worktops. Please take careful note of the inset diagram. 64 Installation The hob can be installed Flush fit hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. [. . . ]