User manual BEKO DVC6531

[. . . ] ­ Buzzer Allows the buzzer to sound as the drum rotates during the anti-crease cycle. ­ Start Starts the selected program (it does not stay pushed in). Indicator lamps ­ Empty out container The water container should be emptied. ­ PROGRAM SEQUENCE The program sequence indicator lamps show the current status of the drying program. ­ DRYING STAGE REACHED These indicator lamps show which drying stage the program has reached. For program stages "Normal" and "Extra dry" the indicator lamp remains at the "Normal" position. [. . . ] If fabric softening is desired, it is more convenient, economical and beneficial to the clothing if a liquid softener is automatically dispensed while the clothes are in the washing machine. Please see the washing machine operating instructions for directions on how to automatically dispense a liquid softener. 9 Notes: Knitted fabrics and flannel sheets tend to shrink when washed for the first time and also when dried. Permanent press items should be briefly spun in the washing machine before drying. Items which are prone to creasing should not be dried in the "PERMANENT PRESS- Normal +" - Program. Drip-dry shirts made of pure cotton may tend to crease, depending on the quality of their finish. Permanent press fabrics tend to crease more as the size of the load increases. Do not dry new dark-colored fabrics together with light-colored items as they may discolor. Program selection Functional description An electronic sensor system monitors the moisture content of the laundry. Once the required degree of dryness is reached, cold air then enters the drum to cool the laundry. To gently dry delicate fabrics, press this button before starting the cycle. ­ Start Starts the selected program. Function of the pushbuttons "PROGRAM SEQUENCE" indicator The program sequence indicator lamps show the current status of the drying program. "DRYING STAGE REACHED" indicator This indicator shows which drying stage the program has reached. "PROGRAM SETTING" selector There is a range of settings for both "Cottons" and "Permanent Press". a cooling-down phase lasting 8 mins. ) or fluffed in a cool air cycle for 15 minutes. ­ Door This button is used to open the door. There are, however, minor problems which can be corrected without contacting the Service Department. What to do if, . If so, failure to start may be due to an incorrect program selection procedure. Remedy . . Repeat the switch-on procedure in the correct sequence, as outlined in the "Program Selection" section. If the "On" indicator lamp does ­ The "ON/OFF" button is not illuminate, check that: depressed. ­ The machine is plugged in and the fuse or circuit breaker has not tripped. The load consisted of dissimilar Select a longer drying items (size and fabrics). the "anti-crease" indicator lamp in the sequence indicator display starts flashing?If the indicator lamp starts flashing again, this indicates a fault in the machine. Please contact the Miele Service Dept. 18 Correcting minor faults What to do if, . the drum door opens during the drying cycle? Problem solving guide Remedy . . Before restarting the program, proceed as follows: ­ Release the ON/OFF button. These two seals may occasionally cause condensed water to form on the door. [. . . ] The receptacle has to be connected to Line 1, Line 2, Neutral and Ground wires. The voltage is 120/240 V AC or 120/208 V AC. Warning Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. "EASY INSTALLATION KIT" If you do not have a designated line, 4 wire, 120/240 V ­ 15 or 30 Amps, for this appliance, but you have the 4 wire, 120/(208)240 V ­ 30 Amp Canadian dryer wall receptacle (14-30 R) you can use the Miele Double Receptacle Box. [. . . ]