User manual BEKO CGA963

[. . . ] Electric Connection Note: Verify the data label placed inside the appliance: - If the symbol ( ) appears on the plate, it means that no earth connection must be made on the appliance, therefore follow the instructions concerning insulation class II. - If the symbol ( ) DOES NOT appear on the plate, follow the instructions concerning insulation class I. Insulation class II The appliance has been manufactured as a class II, therefore no earth cable is necessary. The plug must be easily accessible after the installation of the appliance. [. . . ] If the appliance is connected directly to the electricity supply, an omnipolar switch with a minimum contact opening of 3 mm must be placed in between the two; its size must be suitable for the load required and it must comply with current legislation. If the hob is electric, gas, or induction, the minimum distance between the same and the lower part of the hood must be at least 65 cm. If a connection tube composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source. Before proceeding with the assembly operations, remove the anti-grease filter(s) (Fig. If a pipe with a smaller diameter is used, the efficiency of the product may be reduced and its operation may become noisier · Hood assembly Remove the structure from the packaging and remove the 2 screws A to separate the upper part from the lower part (Fig. Make 4, Ø8 holes in the ceiling and drive in 3 screws without completely tightening them. Pay attention not to insert the screw into the hole marked with an X on the hole template (the screws and expansion plugs must be suitable for the type of wall). 4) and insert the 3 slots onto the 3 screws that are not completely tightened. Drive in the fourth screw X and tighten the remaining 3 to allow definitive blocking of the upper part of structure B - Take the lower part of the telescopic structure C and insert it into the upper structure B (Fig. Suction version: fix the flexible pipe to the prepared air evacuation hole (Fig 7). To replace the halogen light bulbs B, remove the glass pane C using a lever action on the relevant cracks. In order to replace the dichroic lamps, carefully remove the lamp from the lamp holder with the help of a small flat screwdriver or a similar tool. In doing this operation, please take care If the cooker hood is at speed level 1 it will not be necessary to depress the push-button to switch the cooker hood off. Touching the key at 3rd speed, the intensive function runs for 10', then the appliance go back to work at the original speed. Key E = The Timer times the functions on activation for 15 minutes, after which they are switched off. When the Timer is activated the decimal point must flash on the display. The "clean air" function is activated by pressing key E for 2 seconds when the appliance is switched off. This switches the motor on for 10 minutes every hour at the first speed. During functioning a rotary movement of the peripheral segments must be visualised on the display. When this time has passed the motor switches off and the fixed letter "C" must be visualised on the display until the motor re-starts after 50 minutes for another 10 minutes and so on. Press any key apart from the light keys to return to normal functioning. [. . . ] 23 A): A = LIGHT B = OFF/SPEED I C = SPEED II D = SPEED III E = AUTOMATIC STOP TIMER ­ 15 minutes (*) F = FILTER SATURATION RESET LIGHT When the "filter saturation" light flashes, the anti-grease filters must be washed. When the light comes on without flashing, the anti-grease filters must be washed and the carbon filters replaced (in case of operation whit the recycling version). 23B) key symbols are explained below: A = LIGHT B = OFF C = SPEED I If your appliance does not have the INTENSIVE speed function, press key E for two seconds and it will be activated for 10 minutes after which it will return to the previously set speed. By pressing key F for two seconds (with the hood switched off ) the "clean air" function is activated. [. . . ]