User manual AUDIOVOX JMD200

[. . . ] When Washing your Vehicle Do not expose the product to water or excessive moisture. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. Use the Proper Power Supply This product is designed to operate with a 12 volt DC negative ground battery system. Protect the Disc Mechanism Avoid inserting any foreign objects into the disc slot. [. . . ] If unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn off ignition switch and proceed with final mounting of the chassis. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dash opening, bend tabs outward so that the sleeve is firmly secured to the dashboard. Carefully slide the radio into the mounting sleeve making sure it is right side up until it is fully seated and the spring clips lock it into place. Attach one end of the perforated mounting strap (supplied) to the screw stud on the rear of the chassis using the flange nut provided. If your radio requires the use of an installation kit to mount this radio, follow the instructions included in the kit to attach the radio to the mounting plate supplied with the kit. Install the radio/mounting plate assembly to the sub-dash according to the instructions of the installation kit. Attach the support strap to the radio and dashboard as described above. Replace the dashboard trim panel. M O UN TIN G T A B DE TAILS C UT AW AY V IEW O F M OU NT IN G SU RF ACE TO P TA B BEN D S IDE V IEW U PW AR D 90 ° M O U NT IN G SUR F ACE M OU NT IN G SLEE VE 3. 4. 5. 6. B END TAB S B OTTO M TA B B EN D DO W N W ARD 90 ° 3 JMD200 Wiring Diagram 4 JMD200 Reconnecting the Battery When wiring is complete, reconnect the battery negative terminal. Removing the Unit To remove the radio after installation, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. 5 JMD200 BASIC OPERATION NOTE: CD mode will be skipped if no CD is inserted. Reset Use a ball point pen or thin metal object to press the RESET button (11). The reset button should be activated for the following reasons: LOUD INT · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display PUSH POWER Audio Menu With the radio on, press the SEL button/rotary encoder (1) on the control panel to access the audio menu. You can navigate through the audio menu items by pressing the SEL button repeatedly. Once the desired menu item appears on the display, adjust that option by turning the rotary encoder within 5 seconds. The unit will automatically exit the audio menu after five seconds of inactivity. BASS Level Use the rotary encoder to adjust the Bass level range from "-7" to "+7". TREBLE Level Use the rotary encoder to adjust the Treble level range from "-7" to "+7". Balance (BAL) Use the rotary encoder to adjust the Balance between the left and right speakers from "L15" (full left) to "R15" (full right). Fader (FAD) Use the rotary encoder to adjust the Fader between the rear and front speakers from "R15" (full rear) to "F15" (full front). LOUD Use the rotary encoder (1) to turn the LOUD feature "on" or "off". "Off" is the default setting. Power On/Off Press the rotary encoder POWER button (1) to turn the unit on. [. . . ] This type of noise can be easily detected because it will vary in intensity of pitch with the speed of the engine. Usually, the ignition noise can be suppressed considerably by using a radio suppression type high voltage ignition wire and suppressor resistor in the ignition system. (Most vehicles employ this wire and resistor but it may be necessary to check them for correct operation. ) Another method of suppression is the use of additional noise suppressors. These can be obtained from most professional mobile electronics retailers. Interference Radio reception in a moving environment is very different from reception in a stationary environment (home). [. . . ]