User manual AUDIOLAB 8000M

[. . . ] Accidental damage, faults caused by commercial use, acts of God, incorrect installation, connection or packaging, misuse, neglect or careless operation or handling of the product which is not in accordance with Audiolab's user instructions. Equipment that has been operated in conjunction with unsuitable, inappropriate or faulty apparatus. Products sold 'as is', 'as seen' or 'with all faults'. Repairs or replacements as provided under this warranty are the exclusive remedy of the consumer. Audiolab shall not be liable for any incidental or consequential damages for breach of any express or implied warranty in this product. [. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Class II construction double insulated. Power Cord: An AC power cord is normally supplied with a mains plug suitable for your area. If you have any doubts, consult your dealer about obtaining a suitable power cord. Important notice to UK users The appliance cord is terminated with a UK approved mains plug fitted with a 5A fuse. If the fuse needs to be replaced, an ASTA or BSI approved BS1362 fuse rated at 5A must be used. If you need to change the mains plug, remove the fuse and dispose of this plug safely immediately after cutting it from the cord. Connecting a Mains Plug The wires in the mains lead are colouredin accordancewith the code: Blue: NEUTRAL; Brown: LIVE: As these colours may not correspond to the coloured markings identifying the terminalsin your plug, proceedas follows: The BLUE wire must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The BROWN wire must be connected to the terminal marked with the letter L or coloured BROWNor RED. 5A FUSE BS 1362 BLUE (Neutral) BROWN (Live) 7: Specifications 8000Q Pre-amplifier Inputs: Gain and Sensitivity CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2: IMPEDANCE: 20k GAIN: Adjustable by 3dB steps 0 -15dB. , corresponding to SENSITIVITY(nom. ): 100, 140mV, 200mV, 283mV, 400mV, 562mV HEADPHONES: Gain adjustable 18dB - 33dB in 3dB steps Signal To Noise Ratio (IHF, rel. 0. 5V output) Any input, any gain setting: 97dB Headphones: 80dB Frequency Response 10 Hz-20 kHz ±0. 2 dB: 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 007 % ref 7. 7V rms, 20Hz - 20kHz Channel Balance Within 1 dB Channel Separation Better than100 dB @ 1 kHz any input, any setting Pre-amp Output Max. Output >7. 7 V RMS (20dBm); Output impedance 75 Headphone Output >7. 7Vrms;100 (for headphones 8 -2 k impedance) Record Output VIDEO OUT, TAPE 1 OUT, TAPE 2 OUT: Gain 0 dB (x1); 100 Muting Attenuation>63 dB, controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 15 VA Dimensions (WXHXD) 445x74x335 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 6 kg Shipping:7. 3 kg 8000P Power Amplifier Rated Output Power 100W (20dBW) /Channel into 8 both channels driven Input 1V rms for 100W into 8 Input Impedance: 50k Load Connected in parallel with INPUT Gain 29. 0 dB at1kHz Signal To Noise Ratio (IHF, rel. 0. dBW) Better than 95 dB Frequency Response 20 Hz-20 kHz ±0. 3 dB 0. 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 05 % Channel Balance Within 1 dB Polarity (Phase) Non-Inverting Muting Muting controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60 Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 500 VA Dimensions (WXHXD) 445x74x337 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 8. 7 kg Shipping:10 kg 8000M Power Amplifier Rated Output Power 125W (21dBW) /Channel into 8 , 20Hz - 20kHz Input Sensitivity 1. 12V rms for 120W into 8 Input Impedance: 50k Load Connected in parallel with INPUT Gain 29. 0 dB at1kHz Signal To Noise Ratio (IHF, rel. 0. dBW) Better than 96 dB Frequency Response 20 Hz-20 kHz ±0. 3 dB 0. 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 05 % Polarity (Phase) Non-Inverting Muting Muting controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 300 VA Dimensions (WXHXD) 445x74x337 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 8. 2 kg Shipping:9. 6 kg Audiolab reserves the right to alter design and specification without notice. Audiolab is a member of the International Audio Group. 5: Operation Switching On Make sure all the signal and loudspeaker connections to and from the amp are secure and correctly made. 15 Walpole Park South Walpole MA 02081 USA Tel: +1 508 850 3950 Fax +1 508 850 3905 Servicing Servicing of Audiolab products should only be carried out by authorised service agents. If service is required the equipment should be returned, securely packaged, preferably using original packaging, to your dealer. In the USA equipment may be returned to the Service address shown on this page. Always telephone before returning any equipment. Bi-Amplified connection- 8000Q with four 8000M power amplifiers RIGHT LEFT 2a: Introduction- 8000Q 800Q HEADPHONE SOCKET GAIN SWITCH VOLUME CONTROL INPUT SELECTOR RECORD SELECTOR REMOTE CONTROL SENSOR MUTE LED RED=Mute On POWER LED RED=Power On POWER SWITCH Unpacking Unpack the product fully. [. . . ] Connect the Positive RED (+) terminal of the amplifier to the Positive (+) RED terminal of the loudspeaker. When bi-wiring loudspeakers, make sure you remove the straps connecting the HF and LF terminal pairs. 8000M - Bi-Wired Loudspeaker Connection Bi-wiring offers improved sound quality because high and low frequency signals are carried individually to the loudspeaker drive units. RIGHT LEFT Pre-Amp Left Output 7mm 20mm Speaker Cables RED BLACK Pre-Amp Right Output 8000P - Bi-Amplified Loudspeaker Connection The principle of Bi-wiring can be extended by using a dedicated power amplifier for each loudspeaker drive unit Pre-Amp Output Connecting Cables Standard and Bi-Wired loudspeaker connections using the 8000P are shown in Section 3a. 2b: Introduction- 8000P & 8000M 8000P POWER LED RED=Power On POWER SWITCH 8000M POWER LED RED=Power On POWER SWITCH Unpacking Unpack the product fully. Each carton should contain ( The appropriate Audiolab Power Amplifer ( One IEC power cord suitable for your area ( This instruction manual Report any damage or shortage to your dealer as soon as possible. If you dispose of the packing, do so with regard to any recycling regulations in your area. Power Switch When any Audiolab power amplifier is switched on, the output remains muted for 8 seconds. [. . . ]