User manual ASUS TS500-E2

[. . . ] NCLV-D2 Series NCLV-D2/SATA NCLV-DS2 Motherboard E2040 First Edition V1 August 2005 Copyright © 2005 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] To display the sub-menu, select the item and press <Enter>. 4. 2. 6 Configuration fields These fields show the values for the menu items. If an item is userconfigurable, you can change the value of the field opposite the item. A configurable field is enclosed in brackets, and is highlighted when selected. To change the value of a field, select it then press <Enter> to display a list of options. Refer to "4. 2. 7 Pop-up window. " 4. 2. 7 Pop-up window BIOS SETUP UTILITY Advanced APM Configuration Use [ENTER], [TAB], or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select a menu item then press <Enter> to display a pop-up window with the configuration options for that item. Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out(Minute) Throttle Slow Clock Ratio Power Button Function Restore on AC Power Loss Power Power Power Power Power On On On On On by PS/2 Keyboard by PS/2 Mouse Ring PME# RTC Alarm [Enabled] [Suspend] [Suspend] [Disabled] [50%] [On/Off] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] 4. 2. 8 Scroll bar +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit A scroll bar appears on the right side Pop-up window of a menu screen when there are items Scroll bar that do not fit on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the other items on the screen. 4. 2. 9 General help At the top right corner of the menu screen is a brief description of the selected item. 4-12 Chapter 4: BIOS setup 4. 3 Main menu When you enter the BIOS Setup program, the M a i n menu screen appears, giving you an overview of the basic system information. Refer to section "4. 2. 1 BIOS menu screen" for information on the menu screen items and how to navigate through them. BIOS SETUP UTILITY Security Boot Main Advanced Server Exit Use [ENTER]. Use [+] or [-] to configure system time. System Overview System Time System Date Legacy Diskette A IDE Configuration Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Tertiary IDE Master Fourth IDE Master System Information [11:10:19] [Thu 04/21/2005] [1. 44M, 3. 5 in] [Not [Not [Not [Not [Not [Not Detected] Detected] Detected] Detected] Detected] Detected] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02. 58 (C)Copyright 1985-2004, American Megatrends, Inc. 4. 3. 1 4. 3. 2 4. 3. 3 System Time [xx:xx:xx] System Date [Day xx/xx/xxxx] Legacy Diskette A [1. 44M, 3. 5 in. ] Allows you to set the system time. Allows you to set the system date. Sets the type of floppy drive installed. Configuration options: [Disabled] [360K, 5. 25 in. ] [1. 2M , 5. 25 in. ] [720K , 3. 5 in. ] [1. 44M, 3. 5 in. ] [2. 88M, 3. 5 in. ] ASUS NCLV-D2 Series 4-13 4. 3. 4 IDE Configuration The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press <Enter> if you wish to configure the item. BIOS SETUP UTILITY Main IDE Configuration Onboard IDE Operate Mode Enhanced Mode Support On Configure S-ATA as RAID IDE Detect Time Out (Sec) [Enhanced Mode] [S-ATA] [No] [35] Set [Compatible Mode] when Legacy OS (i. e. WIN2000, WIN XP) is used. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02. 58 (C)Copyright 1985-2004, American Megatrends, Inc. Onboard IDE Operate Mode [Enhanced Mode] Allows selection of the IDE operation mode depending on the installed operating system (OS). Configuration options: [Compatible Mode] [Enhanced Mode] The items E n h a n c e d M o d e S u p p o r t O n and C o n f i g u r e S - A T A a s R A I D appear only when you set the Onboard IDE Operate Mode to [Enhanced Mode]. Enhanced Mode Support On [S-ATA] Allows you to set Serial ATA, Parallel ATA, or both, to native mode. Configuration options: [P-ATA+S-ATA] [S-ATA] [ P-ATA] Configure S-ATA as RAID [No] Allows you to configure the Serial ATA devices as RAID sets. Configuration options: [No] [Yes] IDE Detect Time Out (Sec) [35] Selects the time our value (in seconds) for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 4-14 Chapter 4: BIOS setup 4. 3. 5 Primary/Secondary IDE Master/Slave, Tertiary and Fourth IDE Master The BIOS automatically detects the connected IDE devices. Select a device item, then press <Enter> to display the IDE device information. BIOS SETUP UTILITY Main Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20. 0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : Supported Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type LBA/Large Mode Block(Multi-sector Transfer) PIO Mode DMA Mode SMART Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] Select the type of device connected to the system. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit v02. 58 (C)Copyright 1985-2004, American Megatrends, Inc. The BIOS automatically detects the values opposite the dimmed items (Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These items show N/A if no IDE device is installed in the system. Type [Auto] Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the appropriate IDE device type. Select [ARMD] (ATAPI Removable Media Device) if your device is either a ZIP, LS-120, or MO drive. Configuration options: [Not Installed] [Auto] [CDROM] [ARMD] LBA/Large Mode [Auto] Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the device supports this mode, and if the device was not previously formatted with LBA mode disabled. Configuration options: [Disabled] [Auto] Block (Multi-sector Transfer) [Auto] Enables or disables data multi-sectors transfers. [. . . ] x k e r n e l s the driver is installed in: s, /lib/modules/<kernel_version>/kernel/drivers/net/ bcm5700. o For 2 . x k e r n e l s w i t h b c m 5 7 0 0 d r i v e r p a t c h e d i n the driver n, is installed in: /lib/modules/<kernel_version>/kernel/drivers/net/bcm/ bcm5700. o or /lib/modules/<kernel_version>/kernel/drivers/addon/ bcm5700/bcm5700. o 4. Load the driver: insmod bcm5700 Refer to Linux distribution documentation to configure the network protocol and address. 6-12 Chapter 6: Driver installation Building the driver from the TAR file To build the driver from the TAR file: 1. Create a directory and extract the TAR files: tar xvzf bcm5700-<version>. tar. gz Build the driver bcm5700. o as a loadable module for the running kernel: cd bcm5700-<version>/src make Test the driver by loading it: insmod bcm5700. o Install the driver and man page: make install See the RPM instructions on the previous page for the location of the installed driver. 3. [. . . ]