User manual ASUS P5P800-VM

[. . . ] Motherboard P5P800-VM E2538 Revised Edition V2 March 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ("ASUS"). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] ATX12V ATXPWR +3. 3VDC -12. 0VDC GND PS_ON# GND GND GND -5. 0VDC +5. 0VDC +5. 0VDC +3. 3VDC +3. 3VDC GND +5. 0VDC GND +5. 0VDC GND PWR_OK +5VSB +12. 0VDC +12V DC GND ® P5P800-VM ATX power connector 8. Front panel audio connector (10-1 pin FP_AUDIO) This connector is for a chassis-mounted front panel audio I/O module that supports legacy AC `97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. P5P800-VM +12V DC GND FP_AUDIO P5P800-VM ® P5P800-VM Front panel audio connector ASUS P5P800-VM BLINE_OUT_R +5VA AGND BLINE_OUT_L Line out_L NC Line out_R MICPWR MIC2 1-31 9. USB connectors (10-1 pin USB56, USB78) These connectors are for USB . 0 ports. Connect the optional USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. P5P800-VM GND USB_P5+ USB_P5USB+5V ® USB56 P5P800-VM USB 2. 0 connectors 1 USB78 Never connect a 1394 cable to the USB connectors. Internal audio connectors (4-pin CD) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, MPEG card or modem. Right Audio Channel Ground Ground Left Audio Channel ® P5P800-VM CD(Black) P5P800-VM Internal audio connectors 1-3 Chapter 1: Product introduction NC GND USB_P6+ USB_P6USB+5V USB+5V USB_P7USB_P7+ GND 1 USB+5V USB_P8USB_P8+ GND NC 11. System panel connector (0-1 pin PANEL) This connector supports several chassis-mounted functions. PLED PLED+ PLED- SPEAKER +5V Ground Ground Speaker P5P800-VM PANEL IDE_LED+ IDE_LEDExtSMI# Ground PWR Ground Reset Ground ® IDE_LED RESET PWRSW SMI P5P800-VM System Panel connector * Requires an ATX power supply. The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details. · System power LED (-pin PLED) This -pin connector is for the system power LED. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. System warning speaker (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. Hard disk drive activity (-pin IDE_LED) This -pin connector is for the HDD Activity LED. The IDE LED lights up or flashes when data is read from or written to the HDD. System Management Interrupt Lead (-pin SMI) This -pin connector allows you to manually place the system into a suspended mode, or "green" mode, where system activity is instantly decreased to save power and to expand the life of certain system components. Power/Soft-off button (-pin PWRSW) This connector is for the system power button. Pressing the power button turns the system ON or puts the system in SLEEP or SOFT-OFF mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF. Reset button (-pin RESET) This -pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. · · · · · ASUS P5P800-VM 1-33 1-34 Chapter 1: Product introduction This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS setup 2 2-1 ASUS P5P800-VM 2. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk. ) ASUS EZ Flash (Updates the BIOS using a floppy disk during POST. ) ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted. ) ASUS Update (Updates the BIOS in Windows® environment. ) Refer to the corresponding sections for details on these utilities. Save a copy of the original motherboard BIOS file to a bootable floppy disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFUDOS utilities. 2. 1. 1 1. Creating a bootable floppy disk Do either one of the following to create a bootable floppy disk. Select Create an MS-DOS startup disk from the format options field, then click Start. Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. [. . . ] To change the user password, follow the same steps as in setting a user password. ASUS P5P800-VM 2-33 Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] 2-34 Chapter 2: BIOS setup 2. 7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Pressing <Esc> does not immediately exit this menu. [. . . ]