User manual ASUS P4U800-X

[. . . ] P4U800-X User Guide Motherboard E1882 Checklist Revised Edition V3 January 2005 Copyright © 2005 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] USB header (10-1 pin USB56) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The module has two USB 2. 0 ports for connecting next generation USB peripherals such as high resolution cameras, scanners, and printers. P4U800-X ® USB56 P4U800-X USB 2. 0 connector · · The USB 2. 0 module is purchased separately. Install the USB 2. 0 driver before using the USB 2. 0 feature. 1-18 Chapter 1: Product introduction USB+5V USB_P7USB_P7+ GND 1 USB+5V USB_P8USB_P8+ GND NC GND +12V Rotation 7. Front panel audio connector (10-1 pin FP_AUDIO) This is an interface for the front panel cable that allows convenient connection and control of audio devices. Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable. P4U800-X FP_AUDIO MIC2 MICPWR Line out_R NC Line out_L AGND +5VA BLINE_OUT_R BLINE_OUT_L ® P4U800-X Front panel audio xonnector 8. Chassis intrusion connector (4-1 pin CHASSIS1) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. By default, the pins labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. If you wish to use the chassis intrusion detection feature, remove the jumper cap from the pins. P4U800-X ® CHASSIS1 (Default) P4U800-X intrusion connector ASUS P4U800-X motherboard +5VSB_MB Chassis Signal GND 1-19 9. GAME/MIDI connector (16-1 pin GAME) This connector supports a GAME/MIDI module. If a GAME/MIDI module is available, connect the GAME/MIDI cable to this connector. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files. P4U800-X R GAME P4U800-X Game connector MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V The GAME/MIDI module is purchased separately. 11. System panel connector (10-1 pin PANEL1) This connector accommodates several system front panel functions. Speaker Connector +5V Ground Ground Speaker PWR Ground Power LED PLED+ P4U800-X IDE_LED+ IDE_LED- PLED- +5V J1B2 J1CY GND GND J1CX J1B1 +5V Reset SW ATX Power Switch* ® IDE_LED P4U800-X System panel connector * Requires an ATX power supply. · System Power LED Lead (Green 3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. · System Warning Speaker Lead (Orange 4-pin SPKR) This 4-pin connector connects to the case-mounted speaker and allows you to hear system beeps and warnings. 1-20 Chapter 1: Product introduction Reset Ground · Reset Switch Lead (Blue 2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power. · ATX Power Switch/Soft-off Switch Lead (Light Green 2-pin PWR) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. · Hard Disk Activity Lead (Red 2-pin IDE_LED) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up. The System Panel connector is color-coded for easy and foolproof connection. Take note of the specific connector colors as described. ASUS P4U800-X motherboard 1-21 1-22 Chapter 1: Product introduction Chapter 2 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS information ASUS P4U800-X motherboard 2-1 2. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. AwardBIOS Flash Utility (EZ Flash feature that updates the BIOS using a floppy disk during POST. ) 2. [. . . ] Configuration options: [Disabled] [Enabled] Boot Up Floppy Seek [Disabled] When enabled, the BIOS will seek the floppy disk drive to determine whether the drive has 40 or 80 tracks. Configuration options: [Disabled [Enabled] 2-26 Chapter 2: BIOS information Boot Up NumLock Status [On] Allows you to select the power-on state of the NumLock. Configuration options: [On] [Off] APIC Mode [Enabled] When enabled, this option allows you to distribute interrupt routings other than the 16 IRQs. The Programmable Interrupt Controller (PIC) setting allows you to use the 16 IRQs only. [. . . ]