User manual ASUS P4P800S-E DELUXE

[. . . ] P4P800S-E Deluxe User Guide Motherboard E1383 Checklist First Edition September 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] While the tests are running, the BIOS beeps (see BIOS beep codes table below) or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance. AMI BIOS beep codes No. of Beeps 2 3 4 6 7 8 10 Description Parity error Main memory read/write test error Motherboard timer not operational Keyboard controller BAT test error General exception error Display memory error CMOS shutdown register read/write error 7. Follow the instructions in Chapter 4. ASUS P4P800S-E Deluxe motherboard user guide 3-1 3. 2 Vocal POST Messages This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST ReporterTM. This feature gives you vocal POST messages and alerts to inform you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem. These POST messages are customizable using the Winbond Voice Editor software that came with your package. Following is a list of the default POST messages and their corresponding actions, if any. POST Message No CPU installed System failed CPU test Action · Install an Intel Pentium 4 Processor into the CPU socket. · Install 184-pin unbuffered PC3200/2700/2100 DIMMs into the DIMM sockets. · Check if the DIMMs on the DIMM sockets are properly installed. · Refer to section "2. 5 System memory" for instruction on installing a DIMM. · Install a PCI VGA card into one of the PCI slots, or a +0. 8V/1. 5V AGP card into the AGP slot. · Check your CPU settings in BIOS and make sure you only set to the recommended settings. System failed memory test System failed VGA test System failed due to CPU over-clocking 3-2 Chapter 3: Powering up POST Message No keyboard detected Action · Check your keyboard if properly connected to the purple PS/2 connector on the rear panel. · See section "1. 4. 1 Major components" for the location of the connector. · Make sure you have connected a floppy disk to the floppy disk connector on the motherboard. · See section "2. 8 Connectors. " · Make sure you have connected an IDE hard disk drive to the one of the IDE connectors on the motherboard. · See section "2. 8 Connectors. " · Check CPU fan if working properly. · Check the CPU fan and make sure it turns on after you applied power to the system. · Make sure that your CPU fan supports the fan speed detection function. See the "ASUS contact information" on page x. No floppy disk detected No IDE hard disk detected CPU temperature too high CPU fan failed CPU voltage out of range System completed Power-On Self Test · No action required Computer now booting from operating · No action required system ASUS P4P800S-E Deluxe motherboard user guide 3-3 3. 3 Powering off the computer You must first exit the operating system and shut down the system before switching off the power. [. . . ] This RAID configuration provides data protection and increases fault tolerance to the entire system. 5. 4. 1 BIOS configuration Follow these steps to set the BIOS items related to the RAID function. Enter the BIOS Setup utility by pressing <Delete> during the Power-On Self Test (POST). See section "4. 2 BIOS Setup program" for more information on entering the Setup utility. From the Main menu, select IDE Configuration to display the sub-menu items. [. . . ]