User manual ASUS P4P800S

[. . . ] P4P800S User Guide Motherboard E1398 Checklist Revised Edition V2 August 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Internal audio connectors (4-pin MODEM, CD IN, AUX IN) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. MODEM1 P4P800S ® Modem-In Ground Ground Modem-Out Right Audio Channel Ground Ground Left Audio Channel CD1(Black) AUX1(White) P4P800S Internal Audio Connectors 8. USB header (10-1 pin USB56, USB78) If the USB ports on the rear panel are inadequate, two USB headers are available for additional USB ports. The USB header complies with USB 2. 0 specification that supports up to 480 Mbps connection speed. This speed advantage over the conventional 12 Mbps on USB 1. 1 allows faster Internet connection, interactive gaming, and simultaneous running of high-speed peripherals. The module has two USB 2. 0 ports that support the next generation USB peripherals such as high resolution cameras, scanners, and printers. You must install the driver before you can use the USB 2. 0 capability. USB+5V USB_P6USB_P6+ GND NC P4P800S ® USB56 P4P800S USB 2. 0 Header USB+5V USB_P5USB_P5+ GND USB78 USB+5V USB_P7USB_P7+ GND 1 1 1-26 Chapter 1: Product introduction USB+5V USB_P8USB_P8+ GND NC 9. Front panel audio connector (10-1 pin FP_AUDIO1) This is an interface for the Intel front panel audio cable that allow convenient connection and control of audio devices. Remove the caps from the Line out_R, BLINE_OUT_R, Line out_L and BLINE_OUT_L jumpers if you want to install an Intel front panel audio cable. AGND +5VA BLINE_OUT_R P4P800S ® FP_AUDIO1 P4P800S Front Panel Audio Connector MIC2 MICPWR Line out_R NC Line out_L 10. GAME/MIDI connector (16-1 pin GAME1) This connector supports a GAME/MIDI module. Connect the GAME/MIDI cable with yellow connector to the yellow header onboard. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files. ® GAME1 P4P800S Game Connector MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V The GAME/MIDI module is purchased separately. ASUS P4P800S motherboard user guide +5V J1B2 J1CY GND GND J1CX J1B1 +5V P4P800S BLINE_OUT_L 1-27 11. System panel connector (20 pin PANEL1) This connector accommodates several system front panel functions. Each group of connector pins match the color of the wire connectors for easier location and identification. Speaker Connector +5V Ground Ground Speaker PWR Ground Power LED PLED+ IDE_LED+ IDE_LEDPLED- P4P800S Reset SW ATX Power Switch* ® IDE_LED * Requires an ATX power supply. P4P800S System Panel Connector · System Power LED Lead (3-1 pin PLED (green)) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. · System Warning Speaker Lead (4-pin SPKR (orange)) This 4-pin connector connects to the case-mounted speaker and allows you to hear system beeps and warnings. · Reset Switch Lead (2-pin RESET (blue)) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power. · ATX Power Switch/Soft-off Switch Lead (2-pin PWR (light green)) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. · Hard Disk Activity Lead (2-pin IDE_LED (red)) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up. 1-28 Chapter 1: Product introduction Reset Ground Chapter 2 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS information 2. 1 Managing and updating your BIOS · · The original BIOS file for this motherboard is in the root directory of the support CD filenamed "P4P800. ROM". Copy the original BIOS to a bootable floppy disk in case you need to restore the BIOS in the future. 2. 1. 1 Creating a bootable floppy disk 1. At the DOS prompt, type: format A:/S , then press the <Enter> key Windows environment a. From your Windows desktop, click on Start, point to Settings, then click on Control Panel. Double-click on Add/Remove Programs icon from the Control Panel window. Copy the original (or the latest) motherboard BIOS to the bootable floppy disk. 2. 1. 2 Using AFUDOS to update the BIOS Update the BIOS using the AFUDOS. EXE utility in DOS environment. Visit the ASUS website (www. asus. com) to download the latest BIOS file for your motherboard. [. . . ] This feature is supported by the onboard audio AC'97 CODEC, and requires an optical drive (CD-ROM, DVD-ROM, or CD-RW). 1. Instant Music Lite does not work if you installed and enabled an add-on sound card. Instant Music Lite only supports PS/2 keyboard. To enable ASUS Instant Music Lite: 1. Connect the analog audio cable from the optical drive (CD-ROM, DVD-ROM, or CD-RW drive) to the 4-pin CD-In connector (labeled CD1) on the motherboard. [. . . ]