User manual ASUS P4P800-MX

[. . . ] P4P800-MX User Guide Motherboard E1880 Checklist Revised Edition V3 January 2005 Copyright © 2005 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] The current Serial ATA interface allows up to 150 MB/s data transfer rate, faster than the standard parallel ATA with 133 MB/s (Ultra ATA133). SATA2 P4P800-MX SATA1 ® P4P800-MX SATA Connectors Parallel ATA and Serial ATA device configurations Following are the Parallel ATA and Serial ATA device configurations supported by Intel ICH5 specifications. ICH5 supports a maximum of four (4) devices using these OS. P-ATA Secondary (2 devices) GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND Operating System 1. Windows® 98/Me/NT4. 0® Configuration A Configuration B Configuration C Legend: Supported Disabled Primary (2 devices) Port 0 (1 device) S-ATA Port 1 (1 device) -- -- -- -- -- 1-22 Chapter 1: Product introduction Required IDE Configuration settings in BIOS Refer to the following table for the appropriate BIOS settings of the above P-ATA and S-ATA device configurations. See "2. 3. 5 IDE Configuration" for details on the related BIOS items. Windows 2000/XP Enhanced Mode BIOS item Onboard IDE Operate Mode A -- Windows 98/Me/NT4. 0 B Compatible Mode C -- Compatible Mode Compatible Mode Enhanced Mode Support On S-ATA IDE Port Settings -- Sec. ATX power connectors (20-pin ATXPWR1, 4-pin ATX12V1) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 20-pin ATXPWR1 connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU. Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate. ATXPWR1 P4P800-MX ATX12V1 GND +12V DC GND +12V DC ® P4P800-MX ATX Power Connector +3. 3VDC -12. 0VDC COM PS_ON# COM COM COM -5. 0VDC +5. 0VDC +5. 0VDC +3. 3VDC +3. 3VDC COM +5. 0VDC COM +5. 0VDC COM PWR_OK +5VSB +12. 0VDC ASUS P4P800-MX motherboard 1-23 5. Internal audio connectors (4-pin CD1, AUX1) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. CD1(Black) AUX1(White) P4P800-MX ® P4P800-MX Internal Audio Connectors 6. Front panel audio connector (10-1 pin FP_AUDIO1) This is an interface for the Intel front panel audio cable that allow convenient connection and control of audio devices. By default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable. P4P800-MX FP_AUDIO1 BLINE_OUT_L BLINE_OUT_R +5VA AGND Line out_L NC Line out_R MICPWR MIC2 P4P800-MX Front Panel Audio Connector 1-24 Chapter 1: Product introduction Left Audio Channel Ground Ground Right Audio Channel 7. Chassis intrusion connector (4-1 pin CHASSIS1) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. By default, the pins labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. If you wish to use the chassis intrusion detection feature, remove the jumper cap from the pins. P4P800-MX CHASSIS1 Chassis Signal GND (Default) MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V +5V J1B2 J1CY GND GND J1CX J1B1 +5V ® P4P800-MX Chassis Alarm Lead 8. Optional GAME/MIDI connector (16-1 pin GAME1) This connector supports an optional GAME/MIDI module. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files. ® P4P800-MX GAME1 P4P800-MX Game Connector The USB 2. 0/GAME module is purchased separately. ASUS P4P800-MX motherboard +5VSB_MB 1-25 9. CPU and chassis fan connectors (3-pin CPU_FAN1, CHA_FAN1) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. [. . . ] Select one of the options from this menu or <F10> from the legend bar to exit. Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. Select [Yes] to save changes and exit. ASUS P4P800-MX motherboard 2-29 If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Pressing <Enter> saves the changes while exiting. Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. [. . . ]