User manual ASUS MY CINEMA-U3100MINI/ISDBT MY CINEMA SERIES USER’S MANUAL(ENGLISH)

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License (“GPL”) and under the Lesser General Public License Version (“LGPL”). [. . . ] Confirm the password when prompted. From the Create New Password box, key in a password, then press <Enter>. To change an administrator password: From the Enter Current Password box, key in the current password, then press <Enter>. Confirm the password when prompted. Select the Administrator Password item and press <Enter>. From the Create New Password box, key in a new password, then press <Enter>. To clear the administrator password, follow the same steps as in changing an administrator password, but press <Enter> when prompted to create/confirm the password. After you clear the password, the Administrator Password item on top of the screen shows Not Installed. User Password If you have set a user password, you must enter the user password for accessing the system. The User Password item on top of the screen shows the default Not Installed. To set a user password: 1. 2. 3. 1. 2. 3. 4. Chapter 3 3-6 Select the User Password item and press <Enter>. Confirm the password when prompted. From the Create New Password box, key in a password, then press <Enter>. To change a user password: From the Enter Current Password box, key in the current password, then press <Enter>. Confirm the password when prompted. Select the User Password item and press <Enter>. From the Create New Password box, key in a new password, then press <Enter>. To clear the user password, follow the same steps as in changing a user password, but press <Enter> when prompted to create/confirm the password. After you clear the password, the User Password item on top of the screen shows Not Installed. Chapter 3: BIOS setup 3. 4 Ai Tweaker menu Be cautious when changing the settings of the Ai Tweaker menu items. The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard. UEFI BIOS Utility - Advanced Mode Exit The Ai Tweaker menu items allow you to configure overclocking-related items. Main Ai Tweaker Advanced Monitor Boot Tool [X. M. P. ] When XMP is enabled BLCK frequency, CPU ratio and memory parameters will be auto optimized. Scroll down to display the following items: →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save ESC: Exit F12: Print Screen ASUS MY CINEMA-U3100MINI/ISDBT 3-7 Chapter 3 →←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save ESC: Exit F12: Print Screen Ai Overclock Tuner [Auto] [Auto] [Manual] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Use the <+> and <-> keys to adjust the value. DIGI+ VRM CPU Load-Line Calibration [Auto] Load-line is defined by Intel VRM specifications, and affects CPU voltage. Higher value gets a higher voltage, and a better overclocking performance, but increases the CPU and VRM thermal conditions. This item allows you to adjust the voltage range from the following percentages to boost the system performance: 0% (Regular), 25% (Medium), 50% (High), 75% (Ultra High) and 100% (Extreme). Configuration options: [Auto] [Regular] [Medium] [High] [Ultra High] [Extreme] The actual performance boost may vary depending on your CPU specification. CPU Fixed Frequency [xxx] This item appears only when you set the CPU Voltage Frequency item to [Manual] and allows you to set a fixed CPU frequency. The values range from 200k Hz to 350k Hz with a 50k Hz interval. CPU Power Phase Control [Standard] Allows you to control the power phase based on the CPU’s demands. Configuration options: [Standard] [Optimized] [Extreme] [Manual Adjustment] DO NOT remove the thermal module when switching to Extreme and Manual Mode. The thermal conditions should be monitored. CPU Power Duty Control [T. Probe] DIGI + VRM Duty control adjusts the current and thermal conditions of every component’s phase. Chapter 3 3-10 [T. Select to maintain the current VRM balance. CPU Current Capability [100%] Allows you to configure the total power range, and extends the overclocking frequency range simultaneously. Configuration options: [100%] [110%] [120%] Choose a higher value when overclocking, or under a high CPU loading for extra power support. iGPU Load-line Calibration [Auto] Allows you to set the iGPU Load-line Calibration. Configuration options: [Auto] [Regular] [High] [Extreme] iGPU Current Capability [100%] Allows you to set the iGPU Current Capability. Configuration options: [100%] [110%] [120%] Do not remove the thermal module while changing the DIGI+ VRM related parrameters . [. . . ] 6. Connect two independent auxiliary power sources from the power supply to the two graphics cards separately. Connect a VGA or a DVI cable to the graphics card. Chapter 5: Multiple GPU technology support 5. 1. 4 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. 5. 1. 5 Enabling the ATI® CrossFireX™ technology After installing your graphics cards and the device drivers, enable the CrossFireX™ feature through the ATI Catalyst™ Control Center in Windows environment. Launching the ATI Catalyst Control Center To launch the ATI Catalyst Control Center: 1. Right-click on the Windows® desktop and select Catalyst(TM) Control Center. You can also right-click the ATI icon in the Windows notification area and select Cayalist Control Center. 2. The Catalyst Control Center Setup Assistant appears when the system detects the existance of multi-graphics cards. Click Go to continue to the Catalyst Control Center Advanced View window. Enabling Dual CrossFireX technology 1. 2. 3. 4. In the Catalyst Control Center window, click Graphics Settings > CrossFireX > Configure. [. . . ]