User manual ASUS M2R-FVM

[. . . ] Motherboard M2R-FVM E2614 First Edition May 2006 Copyright © 2006 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] This port connects the side speakers in an 8-channel audio configuration. ASUS M2R-FVM 1-23 Refer to the audio configuration table below for the function of the audio ports in 2, 4, or 6-channel configuration. Audio 2, 4, 6 or 8-channel configuration Port Light Blue Lime Pink Orange Black Gray 2-channel (Headset) Line In Line Out Mic In -- -- -- 4-channel Line In Front Speaker Out Mic In Center /Subwoofer -- -- 6-channel Line In Front Speaker Out Mic In Rear Speaker Out -- Side speaker out 8-channel Line In Front Speaker Out Mic In Center/Subwoofer Rear Speaker Out Side speaker out 9. USB 2. 0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2. 0 devices. 10. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2. 0 devices. This port connectors an external audio output device via a S/PDIF cable. This 9-pin COM1 port is for serial devices. SPDIF port. 1. 10. 2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY R M2R-FVM PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. M2R-FVM Floppy Disk Drive Connector 1-24 Chapter 1: Product introduction 2. IDE connector (40-1 pin IDE1) These connectors are for Ultra DMA 133/100/66 signal cables. The Ultra DMA 133/100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. · Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. · IDE1 R M2R-FVM NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1. PIN 1 M2R-FVM IDE Connector ASUS M2R-FVM 1-25 3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. The current Serial ATA I interface allows up to 150 MB/s data transfer rate. SATA3 GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA1 GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND R SATA4 GND RSATA_TXP4 RSATA_TXN4 GND RSATA_RXP4 RSATA_RXN4 GND SATA2 GND RSATA_TXP3 RSATA_TXN3 GND RSATA_RXP3 RSATA_RXN3 GND M2R-FVM M2R-FVM SATA Connectors Install the Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 or later before using Serial ATA. 4. Digital Audio connector (3-pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. SPDIF_OUT GND SPDIF +5V R M2R-FVM 1 M2R-FVM Digital Audio Connector The S/PDIF out module is purchased separately. 1-26 Chapter 1: Product introduction 5. CPU and Chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND CHA_FAN1 CHA FAN PWM CHA FAN IN CHA FAN PWR GND R M2R-FVM M2R-FVM Fan Connectors 6. ATX power connectors (24-pin ATXPWR1 and 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · · Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. [. . . ] Configuration options: [Disabled] [Enabled] Boot Up Floppy Seek [Enabled] Enables or disables the floppy seek feature while booting. Configuration options: [Disabled] [Enabled] Bootup Num-Lock [On] Allows you to select the power-on state for the NumLock. Configuration options: [Off] [On] Full Screen LOGO [Enabled] Allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Make sure that the above item is set to [Enabled] if you want to use the ASUS MyLogoTM feature. Halt On [No Errors] Allows you to select error report type. [. . . ]