User manual ASUS AP2400R-E2(AS8)

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Setting this jumper to pins 2-3 disables the Gigabit LAN port (RJ-45) on the rear panel that corresponds to this controller. 1G LAN_EN Enable (Default) PR-DLS533 Disable PR-DLS533 1G LAN Setting 4. SCSI setting (2-pin SCSI_EN) This jumper allows you to enable or disable the onboard SCSI feature. Place a cap on the jumper to disable the onboard SCSI controller. SCSI_EN Enable (Default) PR-DLS533 Disable PR-DLS533 SCSI Setting 4-6 Chapter 4: Motherboard information 5. Clear RTC RAM (R452) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Short solder points to Clear CMOS R452 ASUS ASIC with Hardware Monitor CR2032 3V Lithium Cell CMOS Power PR-DLS533 PR-DLS533 Clear RTC RAM ASUS AP2400R-E2(AS8) 2U barebone server 4-7 4. 3 Connectors This section describes the internal connectors on the motherboard. Refer to section "1. 4 Rear panel features" for information on the external (rear panel) connectors. 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. PR-DLS533 PR-DLS533 Floppy Disk Drive Connector 2. The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate. Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts 12V 12V 12V 12V GND GND GND GND +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts For Power Supply with 20-pin Power Connector 4-pin 8-pin 24-pin Power Connector 1 ATXPWR CON12V PR-DLS533 PR-DLS533 ATX Power Connectors ASUS AP2400R-E2(AS8) 2U barebone server 4-11 7. CPU, Chassis, and Power Fan Connectors (3-pin CPUFAN1, CPUFAN2, SYSFAN1, SYSFAN2, SYSFAN3) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors! SYSFAN3 CPUFAN1 SYSFAN2 GND +12V Rotation Rotation +12V GND CPUFAN2 GND +12V Rotation SYSFAN1 GND +12V Rotation PR-DLS533 PR-DLS533 12-Volt Cooling Fan Power 8. USB header (10-1 pin USB2) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 1. 1 specification that supports up to 12 Mbps connection speed. USB2 6 USB Power USBP3­ USBP3+ GND PR-DLS533 1 USB Power USBP2­ USBP2+ GND NC 10 5 PR-DLS533 USB Header 4-12 Chapter 4: Motherboard information GND +12V Rotation 9. IPMI connector (4-pin IPMI) The Intelligent Platform Management Interface (IPMI) connector is for the ASMC card. Connect the 4-pin ASMC interface cable to this connector. PR-DLS533 PR-DLS533 IPMI Connector 10. Wake-On-LAN Connector (3-pin WOL_CON) This connector supports a LAN card with a Wake-On-LAN output. [. . . ] Configuration options: [Disabled] [Enabled] [POST Only] Event Log Viewer Pressing <Enter> on this item gives you a sub-menu. You will be shown all events such as "no bootable media" or "fan speed out of range". Clear Event Log [Disabled] This field clears the event log recorded on the sub-menu. An IPMI device must be connected to the server for this field to function. [. . . ]