User manual ARCHOS DVR STATION GEN 5 VERSION 3

[. . . ] inTrOduCTiOn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1. Hardware seTup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . sCHeduling TV reCOrdings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 1. reCOrding audiO/VideO manuall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 y 4. 1. [. . . ] Here you can deselect/select a channel or change the number of a channel. setting the ir eMitter · The DVR Station has a high-powered infrared LED, located on the front of the device, at the same place as the infrared receiver (see: How to Use the Remote Control). · It allows your ARCHOS device to communicate with your tuner (VCR, cable box, satellite receiver or Digital TV receiver), so that it can turn it on and off, and change channels on it. · This is a one time step to set your ARCHOS device to send the correct infrared codes to control your tuner. If you do not plan on making scheduled recordings, then you do not need to set the infrared emitter code. From the "TV Control" screen, select "Set Infrared Emitter". This first screen allows you to correctly set the codes and parameters so that the DVR Station can turn your tuner on/off automatically (for a scheduled recording). 4 DVR Station Gen 5 User ManUal - version 3 2. "TV Receiver": select the type of tuner that you want to control with the IR Emitter ("VCR", "Cable/DSL box", "Satellite Receiver", "DVD Recorder" or "Digital TV"). After a few seconds, your ARCHOS will ask you if the device responded correctly: If your tuner turned off, select "Yes", and move on to the next section. If your tuner did not turn off, select "No, try next code". Your device will try turning the tuner off again, using a different code. Repeat this operation until the ARCHOS manages to turn the tuner off. If none of the codes work, check that the DVR Station is positioned in a way that allows the infrared signal to reach your tuner's receiver. Note: In some rare cases the ON/OFF functionality may not work. 2nd test: changing channels on your tuner After you select "Yes" at the end of the 1st test, the following screen appears. It allows you to correctly set the parameters so that the DVR Station can change channels on your tuner (for a scheduled recording). 1. For the "Channel" parameter, select the highest channel that is currently memorized on your tuner. 5 DVR Station Gen 5 User ManUal - version 3 2. Your ARCHOS device will then attempt to switch your tuner to the selected channel. After a few seconds, your ARCHOS will ask you if the device responded correctly: If this worked, select "Yes". Your device will try again to switch your tuner to the selected channel, using a different option*. Repeat this operation until it works. *Here is a description of the different parameters automatically set by the ARCHOS: - "Key Delay": delay between the emission of each digit of a channel ("Short", "Normal", "Long"). - "Key: Enter": Set to "On" if normally, you have to press an "OK" button on your turner's remote control after you enter the channel number. Example: If you normally press 1, 3, "OK" to access channel 13, then this parameter is set to "On". - "Key: -/--": Set to "On" if normally, you need to press a special key on your tuner's remote control before entering a channel with several digit numbers (that is to say a channel greater than 9). - "Time until video": see below. If the ARCHOS did not manage to switch your tuner to the selected channel, you can try using a different ON/OFF code (see: 1st Test: turning your tuner off) and do the 2nd test again. 3. [. . . ] In the progression bar, go to the beginning of the first undesired section (a), select the "Insert a mark" menu item, and choose "Start Mark". Forward to the end of the first undesired section (b), select the "Insert a mark" menu item, and choose "End Mark". Select the "Edit Selection" menu item and choose "Cut", which will cut out this part of the recording. Go to the beginning of the second undesired section (c), select the "Insert a mark" menu item, and choose "Start Mark". [. . . ]