User manual ALPINE PXA-H900

[. . . ] Failure to do so may result in electric shock or injury due to electrical shorts. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. 2-EN DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. [. . . ] After step 2 on page 7, remove the included side bracket. Side bracket Side bracket 2. Mount the display using the included screws. Bracket Spacer Display Pan head screw (M3 x 5) x 2 3. Next, securely mount the factory brackets removed from the factory radio, to the display assembly. Flat head screws (M5 x 8) Bracket 8-EN · Flush Mounting the display 1. Make a cut-out approximately 178 (width) by 50 (height) mm (7 inches by 2 inches) in size at your desired mounting location. WARNING: When making cut-outs, be careful not to damage pipes, tanks, electric wires, etc. Mount the spacer on the display using the included screws. Spacer Display Pan head screw (M3 x 5) x 2 5. Attach the flush mount brackets to the display using the included screws. Flush mount Self-tapping screw (M2. 6 x 8) x 4 Face plate 9-EN · Mounting the base unit 1. WARNING: When making holes, be careful not to damage pipes, tanks, electric wires, etc. Securely mount the unit using the four included flanged self-tapping screws (M4 x 14). Flanged self-tapping screw (M4 x 14) · Mounting Microphone Mounting Location Mount the microphone on the rear-view mirror, headrest, sun visor, or other appropriate location. Peel off the protective papers from the adhesive side of the Velcro fasteners. Attach 2 pieces of the Velcro fasteners on to the microphone holder base and the other side of the Velcro fastener on the spot where the microphone holder base is located. Insert the microphone into the Y-shaped holder on the holder base. 10-EN · Mounting the remote control unit holder · If the remote control unit is exposed to direct sunlight, remove it from the holder and store it in the glove compartment. · If the holder cannot be securely fastened in place with the Velcro, install it using screws. Remote Control Screw for mounting remote control unit holder (M2. 9 x 20) Remote Control Holder Velcro tape Console box, etc. WARNING: Do not install the product near the passenger seat's airbag. Doing so could hamper airbag operation, leading to accidents or injury. 11-EN Connections · Basic Connections Diagram < Ceiling > NOTE Normally the various indicators are lit blue. Dolby Digital Indicator Lights white during Dolby Digital decoding. HDCD Indicator Lights white during HDCD decoding. DTS Indicator Lights white during DTS decoding. MPEG Indicator Lights white during MPEG2 decoding. Note: Remove the 2 screws marked 5 using the included hexagonal wrench (M2. 6). PC CONTROL MIC. Computer terminal Used to make settings and adjustments with a computer. For details, contact your store of purchase or an Alpine Information Center. MEMORY LOCK Reset switch Microphone jack Use this to connect a microphone. Memory on/off selector switch Use this to set whether or not settings and adjustments can be stored in the memory. 12-EN < Side Panel > Cord specifications · Head unit input terminal (optical digital input) Used for system expansion (Ai-NET head unit, etc. ). · Changer input terminal (optical digital input) Used for system expansion (Ai-NET changer, etc. ). · DVD player input terminal (optical digital input) Used for system expansion (DVD player, etc. ). Connect to: Connect to an Ai-NET product using an optical fiber cable. · Ground terminal Connect securely to a metal part of the vehicle's body using the ground cord. · Battery power terminal Power is supplied constantly to the PXA-H900 regardless of whether the engine key is on or off. Connect to: Connect to the amplifier for the front tweeter speaker. [. . . ] Mount the terminal board cover on the PXA-H900. 18-EN R ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel. : (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. Tel. : 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. Markham, Ontario L3R 9Z6, Canada Tel. : 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF AUSTRALIA PTY. [. . . ]