User manual ALPINE CVA-1003RR

[. . . ] Peel off the backing of the adhesive tape and press the sensor onto the selected mounting location, or inside of the remote control holder. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. ' DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. [. . . ] This will reduce any chance of damage to the unit in case of a short-circuit. Incorrect connections may cause the unit to malfunction or damage the vehicle's electrical system. When making connections to the car's electrical system, be aware of the factory installed components (e. When connecting the DVA-5205P to the fuse box, make sure the fuse for the intended circuit of the DVA-5205P has the appropriate amperage. Mount the brackets 1 at both sides of the unit with screws with double washer (M5x10) 3. Attach the unit securely with hex bolts (M6x50) 4, flanged hex nut (M6) 7, spring washers (M6) 6, and wing nuts (M6) 8. 4 Hex bolt (M6x50)/ 5 Flanged self-tapping 6 Spring washer 8 Wing nut (M6)/ 9 Velcro fastener/ p Mounting sleeve/ 7 Flanged head hex nut Boulon à six pans screw (M5x15)/Vis (M6)/Rondelle à Ecrou à oreilles Fermeture Velcro/ Gaine de montage/ (M6)/Ecrou hexagonal à (M6x50)/Perno autotaraudée à ressort (M6)/ (M6)/Tuerca de Cremallera Velcro Manguito de montaje tête à embase (M6)/ hexagonal (M6x50) embase (M5x15)/ Arandela de mariposa (M6) Tuerca hexagonal de Tornillo autorroscante resorte (M6) cabeza embridada (M6) embridado (M5x15) Mount the brackets 1 at both sides of the unit with screws with double washer (M5x10) 3. Mount the unit on the floor with flanged selftapping screws (M5x15) 5 and spring washers (M6) 6. 1 Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position. When connecting with the Ai-NET compatible AV head unit or the Ai-NET compatible head unit, do not connect the ignition lead. 2 Fuse Holder (1A) 3 Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided. 4 Battery Lead (Yellow) Connect this lead to the positive (+) post of the vehicle's battery. 5 Fuse Holder (5A) 6 Remote Control Input Lead (White/Brown) This lead is used in combination with an ALPINE product with a remote control output lead. 7 Video Output Connector This connector is used in combination with the video inputs of another video product (TV monitor). 8 Ai-NET Connector (Black) Connect this to the output or input connector of other product equipped with Ai-NET. Connect this connector to the Digital Audio Processor (PXAH510) or Ai-NET connector of the Head unit (when Digital Audio Processor is not connected). 9 Ai-NET Connector (Gray) Connect this to the output or input connector of other product equipped with Ai-NET. Connect this connector to the Head unit (when the Digital Audio Processor is connected) or to the Ai-NET connector a CD Changer (when the Digital Audio Processor is not connected). p Remote Control Eye Jack Connect this to the remote control sensor unit. Not used when using a monitor with a built-in remote control sensor unit. A remote control sensor unit is needed when a monitor or navigation unit made by other company is connected. [. . . ] If your vehicule does not have the Mounting Support, reinforce the DVD unit with the metal mounting strap supplied. Connect each input lead coming from an amplifier or equalizer to the corresponding output lead coming from the left rear of the DVA-5205P. Connect all other leads of the DVA-5205P according to details described in the "Connections" section. When the unit is in place, make sure the locking pins are fully seated in the down position. [. . . ]