User manual AEG-ELECTROLUX MINETN661VUKYL2K

[. . . ] · The identification plate, with the technical data, serial number and mark, is clearly visible inside the bottle compartment. · Installation and servicing should be carried out by qualified personnel in accordance with current regulations. · Before operating the appliance it is essential to remove the protective film from the interior and exterior. · Immediately after installation, test the appliance briefly using the directions for use. [. . . ] · Do not obstruct the vents at the front and rear of the appliance. · To prevent the combustion of previous cooking residue, clean the drip pan, burners compartment and the burners themselves before each use. · Do not use metal sponges or sharp scrapers on the external surfaces. Use normal non-abrasive products, with wooden or plastic utensils if necessary. Do not use high pressure water jets on the barbecue, the power of the water jet may damage the finish and endanger safety. · The product packing is made of non-polluting, environment friendly and recyclable materials. Dispose of the packing correctly at recycling and disposal centres. The manufacturer declines all responsibility for use other than that indicated, as well as for damage to things or harm to persons caused by failure to comply with these guidelines or by tampering, even partially, with the appliance or by the use of non-original spare parts. electrolux Installation 1 Intended use The barbecue has been designed and built to cook and heat food in the open air. This appliance is not designed for use in a professional setting or in enclosed spaces. Version with trolley and side shelves MODEL EGL9000X MINETN661VUKYL2K NO. BURNERS 4 2 X 1600 1300 Y 975 850 2 electrolux Installation Preliminary operations barbecue connector D. When the gas bottle is inside the chart make the gas tube going trough the hole E then connect following the instruction from point 1 to 3. Fit the rear panels F and G putting in position then pulling down. Before installing and using the barbecue, the interior should be cleaned of any manufacturing residue. For further information on cleaning refer to chapter "Cleaning the barbecue" on page 10. Place the cast iron grids D. To assure a good working, take care that the ceramic tiles holes get not obstructed. Overturn the tiles regularly to let the burners carbonate the cooking residuals. Only in the conditions illustrated above, with all the aforesaid components correctly assembled, is it advisable to start cooking. Any other set-up may constitute a risk for the user and may jeopardise the good use of the appliance. 8 electrolux Use Lighting the burners Each knob indicates the corresponding burner (see "The control panel" on page 4). Press the knob and turn the indicator to the symbol : the ignition clicks and the pilot light switches on simultaneously. To generate other discharges, hold down the knob while turning the indicator repeatedly to the symbol . To switch off the burner return the indicator to ; press the knob and turn the indicator to (burner off) while holding down the knob. F Grills. E B A C F D 1 Cooking tips Some suggestions for getting the best out of your Electrolux barbecue are given below. Please remember that cooking times and intensities may vary according to personal taste and type of food. 2 Never close the lid on this appliance while cooking! 3 4 If the burner does not light, return the knob to ; press the knob and turn the indicator to (burner off) while holding down the knob. Wait a few seconds to allow the gas emitted to disperse and then repeat points 1 to 3. To check the burners have turned on, look for the flame through the slots in the grills. Meat and Fish To cook meat, preheat the grill burners on maximum setting for at least 5-10 minutes, depending on the thickness of the meat. For small pieces (chops, bacon rashers, ribs etc. ) preheat for a short time (approximately 5 minutes). In general, to cook meat, the burners should be set on maximum, and on medium/minimum for fish and vegetables. [. . . ] If this is not effective, disassemble the burners and clean them thoroughly (e. g. putting a pin through the clogged holes and blowing compressed air straight into the burner). Disassembling the burners · Remove the grills A and the griddles B. · To remove the burners D remove the cotter pins F (one per burner); then free the Venturi tube from its seat and take out. [. . . ]