User manual AEG-ELECTROLUX ETN1042H 1KOK

[. . . ] If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualified professional. Do not use multiple sockets or extensions. During installation and Use Warning Move the appliance carefully in order not to damage components of the refrigeration circuit and to avoid gas leaks Warning Avoid prolonged exposure of the appliance to direct sunlight Warning When installing the appliance do not over bend hoses After removing the packaging, make sure the product is complete and undamaged and that all components are present. · Installation must be carried out by qualified professional in compliance with legislation in force in the country of installation. · The packing elements (plastic bags, polystyrene foam, etc. ) should be kept out of reach of children. [. . . ] Extract the screws to continue the mounting. 56 0 mm 8 electrolux Sliding rails installation Position each rail on the side of the cabinet. Please note that there is a specific sliding rail for each side of the cabinet. Each sliding rail should be flush with the support brackets, with spacers when present and with the front of the cabinet. Positioning in the kitchen cabinet Pull the sliding rails completely out, and place the Refreshment Centre on them making sure that the conical pivots match the holes on the base. Fix the Refreshment Centre on the bottom side of the sliding rails with the 2 provided M4x12 screws. 1 Spacer 2 Sliding rail 3 Support bracket Pull out the sliding rail until the cabinet underneath becomes visible. Push back the Refreshment Centre, until it is locked into position. Fix the sliding rail, the support bracket and the spacer with the provided self-threading screws 4. 5x16. When extracting the sliding rails, only one of the frontal holes will become visible. After mounting the corresponding screw, move the rail again to see the second hole and mount the corresponding screw. Check aesthetic alignment with the cabinet and use the provided circular spacers M6x12 for final adjustment. electrolux 9 Frontal spacer installation When included in the package, and if necessary, fix the frontal spacer with the 3 supplied M4x12 screws. 1 Frontal spacer 2 M4x12 screws Unit connection All the operations below require the appliance to be extracted from cabinet. Remove the grid of the drip tray to easily pull out the Refreshment Centre. After extracting the appliance, place the grid back in its original position. Electrical connection Warning Before starting the plug-in, make sure voltage and frequency match the related information on the rating plate and on the technical specifications table. Remove the grid of the drip tray to easily pull out the Refreshment Centre. After extracting the appliance, place the grid back in its original position 2. Remove the safety strip of the CO holder to extract the used bottle 3. Secure the new CO bottle to its holder and fix it with the provided safety strip 6. Push back the appliance until it is locked into position Filter cartridge replacement Warning In case of water leakage dry the base carefully Warning Lay a cloth under the filter cartridge to prevent the base from getting wet electrolux 15 Cleaning of the inlet filter 1 Water inlet and inlet filter housing Carry out this procedure on a yearly basis. Remove the grid of the drip tray to easily pull out the Refreshment Centre. After extracting the appliance, place the grid back in its original position 2. Turn off the appliance using the power switch Water may come out from the filter cartridge, therefore place a cloth on the filter head and cartridge to prevent the cabinet from getting wet. Rotate the used filter cartridge clockwise and pull it down to extract it 4. Insert the new filter cartridge in the filter head by pushing it up and rotating it counter-clockwise 5. Immediately press the ambient water icon and keep it pressed until LEDs start scanning. [. . . ] Check water supply Check if the tap between the water mains and the water inlet hose is open or water is coming out from other taps in the house. When water comes out and the water mains work properly, proceed with the step Check water inlet pressure. If your water mains connection does not work properly, please have it checked. Check water inlet pressure Warning It is recommended to check the CO pressure value when changing the water inlet pressure For further information see the chapter on first installation. Check CO pressure Warning Never exceed the indicated inlet value For further information see the chapter on first installation. [. . . ]