User manual AEG-ELECTROLUX 68001K-MN 79G

[. . . ] 31 3 Operating Instructions 1 Safety instructions 3 5 Please comply with these instructions. This appliance conforms with the following EU Directives: 73/23/EEC dated 19. 02. 1973 Low Voltage Directive 89/336/EEC dated 03. 05. 1989 EMC Directive inclusive of Amending Directive 92/31/EEC 93/68/EEC dated 22. 07. 1993 CE Marking Directive Correct use This appliance should be used only for normal domestic cooking and frying of food. The appliance must not be used as a work surface or as a storage surface. Do not place or store flammable liquids, highly inflammable materials or fusible objects (e. g. [. . . ] The child safety device is set. 11 Releasing the child safety device Step 1. Touch Touch Control panel Switch on the appliance Display/Signal l until the signal sounds Acoustic signal Appliance switches off. The child safety device is released. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Touch Control panel Switch on the appliance and Display/Signal l at the same time / acoustic signal Until the appliance is next switched off, it can used as normal. Switching the power function on and off The power function makes more power available to the induction cooking zones, e. g. After that the induction cooking zone automatically switches back to heat setting 9. Control panel Switch on Switch off Touch Touch Touch Display p 12 Power Management The cooking zones have a maximum power available to them. If this power range is exceeded by switching on the power function, Power Management reduces the heat setting of another cooking zone. The display for this cooking zone alternates for two minutes between the set heat setting and the maximum possible heat setting. Example: Last cooking zone switched on set heat setting Other cooking zone set heat setting 9 display actual heat setting 7 p 7 alternating with 9 3 If the power function has ended, the cooking zones automatically switch back to the heat setting set previously. 13 Using the timer All cooking zones can use each use one of the two timer functions at the same time. Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use 3 3 If a cooking zone is switched off, the timer function set is also switched off. If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. Selecting a cooking zone Step 1. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have Switch the appliance on passed since the appliance again. was switched on The lock is switched on l Switch off the lock (See the section "Locking/unlocking the control panel") Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field The child safety device is switched on l Several sensor fields were touched at the same time The sensor fields are partly Remove the cloth or the covered by a damp cloth or liquid. Safety cut-out has been triggered STOP+GO is activated Switch the appliance on again Switching off STOP+GO The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call your therefore not hot local Service Force Centre. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone h The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function Uncover sensor field Repeated acoustic signal One or more sensor fields (6x), appliance switches off have been covered for longer than 10 seconds Display is switching between two heat settings Power management is reducing the power of this cooking zone See the section "Switching the power function on and off" 21 Problem Possible cause Unsuitable cookware No cookware on the cooking zone Remedy Use suitable cookware Place cookware on the cooking zone f flashes The diameter of the botMove onto a smaller cooktom of the cookware is too ing zone small for the cooking zone Use suitable cookware _ is lit e and number are displayed Overheating protection for Switch off the cooking the cooking zone has been zone. Switch the cooking triggered zone on again Electronics fault Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department 1 3 If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. Repairs to the appliance are only to be carried out by qualified service engineers. If the appliance has been wrongly operated, the visit from the service technician or dealer may not take place free of charge, even during the warranty period. 22 Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. Old appliance 2 The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. [. . . ] When you have cut it to length (add a few mm), press the two ends flush up against one another. 26 Assembly 27 28 Rating Plate 29 Warranty conditions Great Britain Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. [. . . ]